INSTALLATION INSTRUCTION
SS5000 Kleenmaid Maxi Tub
1 PRE-INSTALLATION INSTRUCTIONS
IMPORTANT
Please ensure Household pipes are thoroughly flushed to remove debris before
connecting your laundry tub to pipeworks. To prevent foreign particles damaging the
ceramic cartridge an “ In line” filter is recommended to be installed prior to the mixer.
Maximum temperature 80° C, recommended 5°C to 65°C
Maximum pressure 175 PSI, Minimum 15 PSI.
If hot and cold water presures are significantly different, then a regulator / flow control
devise should be fitted.
REGULATION COMPLIANCE
Comply with current Drainage and Plumbing Regulations as required by your local authority.
Sanitary plumbing shall only be carried out by a Registered Plumber.
DETERMINE SITE
Determine the most suitable position for the laundry tub. It may be used either to the left or right of the
Washing Machine. Allow 10mm clearence between the units. Mark the position on the floor as reference.
PLEASE READ THE ENTIRE INSTRUCTION
BEFORE INSTALLING THE LAUNDRY TUB
MOUNTING SINGLE LEVER UNIT INTO CONSOLE
Remove Mixer and Spray handle from box.
Screw mounting studs firmly into base of mixer unit.
Then thread the flat rubber washer up the flexible hoses to
the base the Mixer unit.
Place Mixer unit into console by threading flexible hoses
through mounting hole. Mounting studs need to pass through
2 small holes inside the mounting hole.
Thread the 'o' ring up the flexible hoses to the base of
theMixer unit then place clamping washer around flexible
hoses and slide over mounting studs ensuring the 'o' ring
is sitting in the pressed groove.
Take the 2 brass sleeve nuts and screw onto studs with
the hex. portion away from the Mixer base. Tighten with
the right size spanner.
Before connecting flexiable hoses check all seals have
remained in the coupling nuts, now connect fitting to
taps and pullout spray hose.
Place spray handle into mixer body and allow hose to
hang free at the rear. Place the weight supplied on to
the hose at the lowest part. This is to help the hand
piece to return to the holder. Photo “A”
A:Fit the four leveling feet supplied to the bottom of the cabinet and
adjust to align with Washing Machine height. Tilt laundry tub slightly
to assist with access. Check top of laundry tub with spirit level.
Ensure the cabinet does not rock.
B:Position laundry tub then cut the house Waste Pipe which
should already be installed to the exact height. The final height
will depend on the Waste Trap dimensions. Connect Waste
Trap to your laundry tub.The extra waste adapter is not required for use
in Australia.
C:To connect hot and cold water pipes to the mains, use suitable
connectors. Standard fittings are available at most Plumbing
Supplies.
NOTE: For installations in Australia an
approved stopcock must be fitted to both hot and cold water
inlet pipes.
D:Unscrew Rear Shelf which for transportation purposes is
mounted at the rear of cabinet (refer diagram below &
PHOTO B).
Fasten the cabinet to the wall either through the holes in the
back flange of the cabinet sides or by the Rear Shelf which in
turn enables the laundry tub to align with the front of the
Washing Machine. Ensure Rear Shelf is fastened to the cabinet
with four screws (supplied). Alternative fastening can be
achieved through the floor.
NOTES
House Plumbing supplied by
the customer
Washing Machine Drain System
supplied with the laundry tub
All dimensions are in
millimeters
991
562
85
Waste Adaptor
( NZ Only)
Apply
Plumbing
PVC glue
Rear shelf flange can be tiled over
Rear
Shelf
560
Max 25
888
170
1
2
3
4
5
PHOTO A
PHOTO B
750873 Issue A
ECN: 04053
Rear
Shelf
Wall
647
Rear shelf transport
mounting position.
Adjustable
Feet
NOTE: For installations
in Australia an approved
stopcock must be fitted
to both hot and cold
water inlet pipes
2 Securing laundry tub
3
4
5
2
1
WATER
MAINS
(20 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce